In order to maintain the technical performance of the workbench at all times, the initial setup, daily operation, and maintenance of the equipment are crucial. If these issues are disregarded, the performance of the equipment may decrease. If not maintained for a long time, it may also cause damage to the equipment, causing the workbench to operate in an incomplete state. Therefore, it is necessary to learn the correct maintenance methods. So, how can we maintain different types of workbenches with different structural designs, such as lean management workbenches and ultra clean workbenches, in a reasonable way? Today, the editor will teach you some methods.

Teach you a few tips for proper maintenance of different workbenches

1、 How to maintain an anti-static workbench?

1. Sealing: This workbench adopts a structure where the positive pressure pollution area is completely surrounded by the negative pressure area.

2. Moreover, before using formaldehyde fumigation to sterilize the workbench, to prevent formaldehyde leakage, it is necessary to first use&quo; Soap bubbles; Perform a sealing inspection on the entire machine.

3. Regularly (usually every two months) measure the wind speed in the work area with an anemometer. If it does not meet the technical parameter requirements, the power supply voltage of the fan can be adjusted.

When the fan voltage is adjusted to a higher level and the wind speed in the working area still does not meet the technical parameter requirements, the high-efficiency air supply filter must be replaced. When replacing the high-efficiency air supply filter, the high-efficiency exhaust filter must also be replaced at the same time. After replacement, use a dust particle counter to check if the sealing around the four sides is good. If there is any leakage, seal it with sealant.

5. The fan does not require special maintenance, but it is recommended to conduct a regular inspection.

2、 How to maintain the ultra clean workbench?

1. Avoid large and intense vibrations as much as possible.

2. It is strictly prohibited to bring items that are prone to dust production into the purification area.

3. According to the cleanliness of the environment, regularly (usually 3 months) remove and clean the filter material (non-woven fabric) from the primary filter (when the filter material contains dust and turns black, it should be cleaned immediately)

Wash or replace.

4. Regularly (usually once a week) sterilize the environment and frequently wipe the UV lamp clean with organic solvents such as alcohol or acetone dipped in gauze to avoid affecting the sterilization effect.

5. Regularly (usually twice a month) use a dust particle counter to measure the cleanliness of the clean area purified with this product. When the measured cleanliness does not meet the required cleanliness, the cause should be identified (whether there is leakage, whether the high-efficiency filter has failed, etc.). If the high-efficiency filter has failed, a new high-efficiency filter should be replaced.

When replacing the high-efficiency filter, first remove the initial efficiency filter and air supply unit, then remove the pressure bar, and then take out the ineffective high-efficiency filter, replace it with a new high-efficiency filter, and replace the removed one in its original position. When replacing the high-efficiency filter, the following precautions should be taken:

a. When handling (unpacking, handling, and installing) new high-efficiency filters, special care should be taken not to break the filter paper.

b. Before installation, it is necessary to carefully check whether there are any leaks in the high-efficiency filter due to transportation or other reasons (by facing the filter towards the bright area for visual inspection).

c. When installing a high-efficiency filter, the arrow mark on the high-efficiency filter should point towards the air outlet.

d. When installing high-efficiency filters, attention should be paid to sealing.

e. When tightening the pressure frame screws, the force should be evenly and appropriately applied to ensure stable and reliable fixation and sealing of the high-efficiency filter, and to avoid deformation of the high-efficiency filter and leakage.

f. After replacing the high-efficiency filter, a dust particle counter should be used to detect leaks, especially scanning and checking around the high-efficiency filter frame.

g. The initial and high-efficiency filters are not within the warranty range.

3、 How to maintain a lean management workbench?

The lean management workbench adopts a combination design, which is easy to disassemble and assemble, stable, and durable; In order to meet the requirements of different occasions, square hole hanging boards, louver hanging rooms, boards, power sockets, casters, lighting fixtures, storage boards, etc. can be installed according to different purposes. Special specifications and styles of workbenches can also be customized according to requirements to meet the needs of production lines, maintenance workbenches, experimental benches, processing operation benches, fitter benches, etc.

Performance

1. It is moisture resistant, corrosion-resistant, does not require oil, does not rust, and does not fade.

2. The temperature coefficient is relatively low and is basically not affected by temperature.

3. It requires almost no maintenance and can be quickly and easily cleaned/wiped, with good accuracy and stability.